Waveshare Core407V, STM32F4 Core Board

  • Overview
  • 1. Core407V is a small STM32 development board that features an STM32F407VET6 device as the microcontroller, supports further expansion. It is ideal for starting application development with STM32F family.
  • 2. As a minimal ready-to-run system, the Core407V integrates USB communication interface, JTAG/SWD programming/debugging interface, clock circuit, USB power management, boot mode selection, and so on.
  • 3. Furthermore, pin headers on the backside allow the Core407V to be plugged-in your application board and act as the MCU core circuit in your system. All the I/O ports are accessible on the pin headers, and the header pitch is designed as 2.54mm.
  • What has On Board
Regular Price CAD58.71 Special Price CAD49.93
In stock
SKU
06-ZY13990393
Features
  • Overview
  • 1. Core407V is a small STM32 development board that features an STM32F407VET6 device as the microcontroller, supports further expansion. It is ideal for starting application development with STM32F family.
  • 2. As a minimal ready-to-run system, the Core407V integrates USB communication interface, JTAG/SWD programming/debugging interface, clock circuit, USB power management, boot mode selection, and so on.
  • 3. Furthermore, pin headers on the backside allow the Core407V to be plugged-in your application board and act as the MCU core circuit in your system. All the I/O ports are accessible on the pin headers, and the header pitch is designed as 2.54mm.
  • What has On Board
  • 1. STM32F407VET6: The high performance STM32 MCU which features:
  • - Core: Cortex-M4 32-bit RISC
  • - Feature: a full set of single-cycle DSP instructions
  • - Operating Frequency: 168MHz, 210 DMIPS/1.25 DMIPS/MHz
  • - Operating Voltage: 1.8V-3.6V
  • - Package: LQFP100
  • - Memories: 512kB Flash, 192+4kB SRAM
  • - MCU communication Interfaces:
  • -- 3 x SPI, 3 x USART, 2 x UART, 2 x I2S, 3 x I2C
  • -- 1 x FSMC, 1 x SDIO, 2 x CAN
  • -- 1 x USB 2.0 high-speed/full-speed device/host/OTG controller with dedicated DMA, ULPI and on-chip full-speed PHY
  • -- 1 x 10/100 Ethernet MAC
  • -- 1 x 8 to 12-bit parallel camera interface
  • - AD & DA converters: 3 x AD (12-bit, 1μs, shares 24 channels); 2 x DA (12-bit)
  • - Debugging/Programming: supports JTAG/SWD (serial wire debug) interfaces, supports IAP
  • 2. AMS1117-3.3 (on bottom side): 3.3V voltage regulator
  • 3. MIC2075 (on bottom side): onboard USB power management device
  • 4. Power supply switch, powered from 5Vin or USB connection
  • 5. Boot mode switch, for configuring BOOT0 pin
  • 6. Power indicator
  • 7. Reset button
  • 8. 8M crystal oscillator
  • 9. 32.768K crystal (on bottom side), for internal RTC with calibration
  • 10. JTAG/SWD interface: for debugging/programming
  • 11. USB connector, used for establishing USB communication between PC and the STM32 development board
  • 12. IO expander (including VCC/GND), all the MCU pins are accessible on expansion connectors for further expansion
  • 13. 5Vin pinheader, 5V power supply is required when using USB HOST/OTG
  • 14. USB jumper
  • - Short the jumper when using USB
  • - Open the jumper to disconnect from I/O ports
  • 15. VBAT selection jumper
  • - Short the jumper to use system power supply
  • - Open the jumper to connect the VBAT to external power, such as battery
  • 16. VREF selection jumper
  • - Short the jumper to connect VREF+/VREF- to VCC/GND
  • - Open the jumper to connect VREF+/VREF- to other custom pin via jumper wire
  • Package Contents
  • 1. Core407V development board x 1
  • 2. USB type A to Mini-B cable x 1
  • 3. Software CD x 1
Packing List
  • Waveshare Core407V, STM32F4 Core Board
  • Original set and packaging
Write Your Own Review
You're reviewing:Waveshare Core407V, STM32F4 Core Board