Specially designed for DJI Mini 4 Pro. It fits the Mini 4 Pro very well. The split tripod design will not block the indicator light, fill light, bottom sensor and heat dissipation hole. It will not open obstacle avoidance and can be used with the STARTRC paddle. Install and use together.
Can effectively increase the distance between the drone and the ground by 20 mm. When the Mini 4 Pro takes off or lands on uneven ground, it can reduce the impact force, allowing the drone to land smoothly, and protect the Mini 4 Pros body, sensors and gimbal camera from damage. This prevents ground debris or water stains from soiling or damaging the drone body, gimbal, and propellers. Effectively improves the Mini 4 Pro drone ability to adapt to the ground environment during takeoff and landing.
Adopting a split quick-release design, the battery can be quickly replaced without disassembly. After disassembly, it is easy to store and carry. It can be stored in the original bag, STARTRC special bag and most bags on the market.
Lightweight materials and lightweight design, the entire landing gear weighs only 11g. The lightweight design will not add extra burden to the Mini 4 Pros flight, and it will not shake or fall off during flight.
Size: front leg 16.5 x 60 x 46mm, rear leg 24.5 x 59 x 36mm
The illuminated tripod is specially designed for DJI Mini 4 Pro drone. It fits the curved surface of the Mini 4 Pro body very well and has a hollow carving design that will not block the indicator lights, fill lights, bottom sensors and heat dissipation holes. It can help you better observe your surroundings when you are flying or taking off or landing in the dark night.
Yellow, green and blue mixed color lights, 3 flashing modes, fast flashing mode, slow flashing mode and constant light mode.
The luminous tripod can increase the distance between the bottom of the Mini 4 Pro and the ground by 20 mm. When the Mini 4 Pro is used at night or on overgrown or bumpy gravel roads, it can reduce the impact and make it easier for no one to use it. The drone lands smoothly, preventing ground debris or water stains from soiling or damaging the drone body, gimbal, sensors and propellers, providing safe landing protection.
Built-in battery, rechargeable and reusable, the charging time is about 30 minutes, and the use time after full charge is about 60 minutes.
Lightweight design. The light-emitting tripod weighs only 18.5 grams and can stably carry the fuselage. The lightweight design will not add extra burden to the Mini 4 Pro flight and will not shake or fall off during flight. It also adopts a foldable and quick-release design that will not damage the drone body, is easy to install, and improves portability.
Heightened landing gear for Mini 4 Pro, effectively increasing the fuselage by 14mm to prevent ground debris from contaminating the fuselage and sensors during takeoff and landing.
It can still take off and land on uneven ground, effectively protecting the safety of the fuselage;
Light weight does not affect flight, triangular structure design, stable and not easy to fall off;
Quick-release design, easy to install and remove.
Main material: ABS
Net weight: 20g
Product size: 7 x 2.3 x 1.8cm (front feet), 5.1 x 4.6 x 2.5cm (rear feet)
Suitable for DJI Mavic 3 / Air 2 / Air 2S / Mini 2 remote control
Small size, light weight, easy to store and carry
Design support feet, which can be positioned and can also share the force, so that the force of the extension bracket is more balanced, and the hand-held remote control is more labor-saving
Double wall thickness and bone design make it have greater load-bearing capacity, no matter how large the flat plate can be easily carried
The clamping width of 12cm allows the tablet to be used with the shell, making installation more worry-free
This modification kit can turn the drone into a handheld gimbal, which can be used for aerial photography or land photography, and can also use the remaining power of the drone to continue shooting in an emergency.
A 1/4 tripod interface is reserved at the bottom, which can be connected to various tripods.
Hand-held can be connected to a tripod for one-hand operation, or you can directly hold the remote control for shooting operation.
Suitable for DJI Mavic 3 / Air 2 / Air 2S / Mini 2 remote control
Small size, light weight, easy to store and carry
Design support feet, which can be positioned and can also share the force, so that the force of the extension bracket is more balanced, and the hand-held remote control is more labor-saving
Double wall thickness and bone design make it have greater load-bearing capacity, no matter how large the flat plate can be easily carried
The clamping width of 12cm allows the tablet to be used with the shell, making installation more worry-free
Non-destructive and quick installation, one-button closure, and will not scratch the machine.
It does not affect the replacement of the battery, which is convenient and quick.
Soft silicone straps, anti-mushroom head locks, tightly bundled and upgraded for protection.
Effectively increase the height by about 30mm. Greatly increases the distance between the fuselage and the ground, effectively preventing the ground debris from damaging or soiling the fuselage and sensors during take-off and landing.
One-piece design, which effectively improves the aircrafts adaptability to the ground environment during takeoff and landing, avoiding debris on the ground from dirtying the aircraft or damaging the lens
Lightweight design, does not affect the flight endurance
Precise fit, quick installation and removal, wear-resistant and durable
Reduce the wear and tear of the tripod and chassis, effectively increase the height by 25mm, prevent scratching the fuselage and gimbal, and can still take off and land under uneven ground conditions
Lightweight and stable frame, can stably carry the fuselage, almost does not affect the flight and endurance
Can be used as a mirror to the end of the bracket, handheld takeoff and landing
Triangular reinforcement design around the perimeter for more stable support
Front and rear use snap-on independent mounting, stable hook front and rear arms, stronger force, more stable
The tripod is designed to lie on the outside, 90 degrees downward shooting will not shoot the tripod
Easy to install, quick release and quick install, pay attention to differentiate the tripod serial number