This battery tester is used for lead-acid starting battery, along with checking the following conditions of the battery, starting up, charging, and loading.
With great design, easy operation, precise reading, complete functions, this tester supply the readings by a large LCD and hints by sound and light when testing.
It utillizes 4-wire Kelvin method to complete collection of a series of complicated data for calculating every testing data with build-in precise circuit and improved digital processor.
Some circuit improvements including polar reversal protection, over voltage input protection, loose lead detection, ensure safety and convenience during testing.
It is suitable for testing leaks in confined spaces and has a 420mm probe.
Put the transmitter DY26-T into a closed container to be tested.
Sense pressurized leaks, detects electrical arcing, and finds falling solenoids, valves and bearings .
Comes with a transmitter that emits an ultrasonic frequency to help locate leaaks that are not pressurized. Enough to emit frequencies the detector can pick up.
Detects any pressurized leaking gas, including chlorofluoro carbon(CFCs), hydrofluoro carbon(HFCs), nitrogen(Ni), carbon dioxid.
Instructions
Put the transmitter DY26-T into a closed container to be tested.
Adjust the sensitivity of the DY26-R for receiver (you can adjust the sensitivity to the maximum at the beginning), and then hold the receiver DY26-R to slowly move along the measured object and listen to the sound from the headphones.
Brake pressure was transmitted by brake fluid, the pressure transmission will out of function once brake fluid including too much water. In order to safe-driving, we must test water ratio scale in brake fluid regularly. The brake fluid tester help us do current maintenance, make sure we drive in safety condition.
HD backlight dual display, support backlight display glare and easy reading day and night.
Operation Manual:
(1). Install one 9V(6F22) battery at the back of tester.(not included)
(2). After inserting the battery, press POWER button to turn on the tester, all LEDs lights turn on with buzzer sounding, which indicates the product self-test is successful.
(3). Press SELECT button, it will locate DOT3 model automatically.
(4). Each time you push the SELECT button, it will recycle from DOT3 to DOT4 to DOT5.1 with the indicator LEDs.
In the process of using decoder, error can be found and diagnosed OBD?? connector link.
You can monitor the OBD interface voltage and ground, showed low voltage.?? Display diagnostic stitching error.
Jump for OBD interface signals. Signal lines such as decoder of 7 to 15?? vehicles online.
Rapid detection of OBD2 diagnostic connector whether every stitch of the?? normal communication.
Replace the battery, save the car data function. When replace the battery,?? plug OBD2 connector into the car, at the same time connect additional power to the control box, so that ensure vehicle data is not lost.
This OBDII Protocol Detector & Break Out Box has wide range of applications??in diagnostics, key programming and chip tuning:
To monitor data steam while performing test on vehicle using a Scantool.?? This makes it possible for you to both execute a test and simultaneously monitor the testing process.
Power supply: 2 batteries of size 7 (not included)
Test range: DOT3/DOT4/DOT5.1
Display: HD backlit display
This product is a handheld vehicle testing device that detects the water content in brake fluid to determine whether the brake fluid needs to be replaced.
It is a highly accurate,easy to use, very beautiful product.
The tester is a new high-tech product that combines automotive brake fluid testing and tire pressure testing. Users can regularly check the water content of the brake fluid of the car, making driving safer and more worry-free Using the right tire pressure can give you greater safery, longer tire life and better fuel consumption, and hope it will protect your safe driving.
Enter tire pressure test:
(1). Press the UP key to start testing the tire pressure. The pressure nozzle is pressed against the tire valve,The measurement results appear on the LCD display.
(2). Read the tire pressure directly on the display.
(3). Press the UP button continuously to convert the measurement unit.
(4). Press and hold the UP button for 3 seconds to turn off or Press the DOWN button to close.
It has two testing holes, you can test two spark plugs meanwhile and and if you suspect any spark plug works improperly you could compare and test to make accurate judgment.
Usage: test spark plug performance and ignition strength
Application range: 12V Gasoline vehicles car spark plugs
Widely application: 100V-240V input voltage .
Test principle: In automobile ignition system, the high-voltage ignition coil generates a high-voltage (10000 volts or more), and the spark plug diverts it form high -tension ignition coil into the cylinder engine, spark between the spark plug electrodes will ignite the mixture. The JF109 could tell the good spark plugs from the bad by the strength of the spark.