In the process of using decoder, error can be found and diagnosed OBD?? connector link.
You can monitor the OBD interface voltage and ground, showed low voltage.?? Display diagnostic stitching error.
Jump for OBD interface signals. Signal lines such as decoder of 7 to 15?? vehicles online.
Rapid detection of OBD2 diagnostic connector whether every stitch of the?? normal communication.
Replace the battery, save the car data function. When replace the battery,?? plug OBD2 connector into the car, at the same time connect additional power to the control box, so that ensure vehicle data is not lost.
This OBDII Protocol Detector & Break Out Box has wide range of applications??in diagnostics, key programming and chip tuning:
To monitor data steam while performing test on vehicle using a Scantool.?? This makes it possible for you to both execute a test and simultaneously monitor the testing process.
Power supply: 2 batteries of size 7 (not included)
Test range: DOT3/DOT4/DOT5.1
Display: HD backlit display
This product is a handheld vehicle testing device that detects the water content in brake fluid to determine whether the brake fluid needs to be replaced.
It is a highly accurate,easy to use, very beautiful product.
The tester is a new high-tech product that combines automotive brake fluid testing and tire pressure testing. Users can regularly check the water content of the brake fluid of the car, making driving safer and more worry-free Using the right tire pressure can give you greater safery, longer tire life and better fuel consumption, and hope it will protect your safe driving.
Enter tire pressure test:
(1). Press the UP key to start testing the tire pressure. The pressure nozzle is pressed against the tire valve,The measurement results appear on the LCD display.
(2). Read the tire pressure directly on the display.
(3). Press the UP button continuously to convert the measurement unit.
(4). Press and hold the UP button for 3 seconds to turn off or Press the DOWN button to close.
It has two testing holes, you can test two spark plugs meanwhile and and if you suspect any spark plug works improperly you could compare and test to make accurate judgment.
Usage: test spark plug performance and ignition strength
Application range: 12V Gasoline vehicles car spark plugs
Widely application: 100V-240V input voltage .
Test principle: In automobile ignition system, the high-voltage ignition coil generates a high-voltage (10000 volts or more), and the spark plug diverts it form high -tension ignition coil into the cylinder engine, spark between the spark plug electrodes will ignite the mixture. The JF109 could tell the good spark plugs from the bad by the strength of the spark.
Function: support to share battery test results and generate reports
Using international conductivity testing technology, it can easily, quickly and accurately measure the actual cold start current capability of the vehicle starting battery, the health status of the battery itself, common faults of the vehicle starting system and charging system, and provide help for maintenance personnel to quickly and accurately find out problem, so as to achieve rapid repair.
Support analysis and reading of important car data such as voltage, internal resistance, cold crank amplifier, battery health and state of charge. It provides accurate results, calculating the cold crankability and aging of the battery, making car repairs faster and more accurate.
Function: support to share battery test results and generate reports
Using international conductivity testing technology, it can easily, quickly and accurately measure the actual cold start current capability of the vehicle starting battery, the health status of the battery itself, common faults of the vehicle starting system and charging system, and provide help for maintenance personnel to quickly and accurately find out problem, so as to achieve rapid repair.
Support analysis and reading of important car data such as voltage, internal resistance, cold crank amplifier, battery health and state of charge. It provides accurate results, calculating the cold crankability and aging of the battery, making car repairs faster and more accurate.
The 3 modes can be switched at will. The mode switch is operated by the physical button on the main body of the electronic pen. Press and release the button to cycle through the three working modes.
The working range is 5-30V, not more than 30V
Both positive and negative voltages can be measured. For the load plug, the probe directly connected to the clip can be combined with the probe of the test pen to directly perform load simulation measurement, which is convenient for fault diagnosis.
Do not approach high-voltage lines to prevent LEDs from being broken down by high voltage.